Installing Gas Logs In A Prefab Fireplace Box
Buy Indoor/Outdoor Masonry Fireplace Kits & Prefabricated Fireplaces. Mason-Lite Lightweight Masonry Fireplace Systems help you realize your dreams of having a fireplace in your master bedroom, upstairs retreat, or even your outdoor patio, without major building infrastructure reinforcement.The restful flicker and comfortable glow of the fire will provide you with years of treasured memories. Masonry fireboxes. Vented fireplaces are sold as complete systems that contain the flue, cap, glass door and all parts for an easy and effortless assembly. For a local gas company like Blue Rhino to install a 100-gallon tank, run a gas line, and hook up the fireplace, the cost typically comes in around $400. B-Vent Gas Fireplaces: Built-in burner system for a b-vent gas fireplace. NOT for Vented Gas Logs NOT for Ventless Gas Logs. B-Vent (or Natural Vent) Gas Fireplaces are built-in to your home just like a prefabricated wood burning fireplace.
- Installing Gas Logs In A Prefab Fireplace Box Insert
- How To Install Gas Logs In Fireplace
- Putting Gas Logs In A Buck Stove
- Putting Gas Logs In A Fireplace Insert
Gas Logs Buying Guide While it would be a big task to add a traditional fireplace to an existing home, new gas log systems have been developed to allow fireplaces to be created easily. Use our guide to explore the benefits of vented and vent free and choose the best gas logs for your fireplace. Many of these fireplaces have aged and are often in need of upgrading in these various ways: 1. Parts replacement of components such as interior linings and chimney caps. Glass fireplace doors - either replacement or initial installation. Energy Saving upgrades - prefabs often spill cold drafts into the home. If there is no gas line installed, there will be knockouts for installing a gas line on either or both sides of the refractory liner inside the fireplace as well as in the sheet metal on the outside of the firebox, if in fact the fireplace was designed to be retrofitted with gas.
Installing Gas Logs In A Prefab Fireplace Box Insert
Turn your wood fireplace into one that uses natural gas by adding a fireplace gas line that will fuel a new fixture or insert. This will require not only a good deal of work, but also material, time, and a some prior knowledge about installing a gas line. Keep in mind that this project can be dangerous if you don't know what you're doing. Any work involving natural gas will require special procedures to avoid gas leaks that can be fatal to you and your family. If you are confident that you can do this project and create a safe result, here are some of the steps you'll need to know and do.
Step 1 – Preparing to Install Your Gas Line
Before buying your materials, measure the distance you'll need to run the new gas line to the fireplace from either an existing line in the home or from a new source. Choose a route that will require few, if any, sharp bends that could kink the pipe and slow the flow of gas. Then, make a list of fittings and the lengths pipe you'll need, and take them with you to the hardware store. Check with your municipal building department for codes you will need to meet as well.
Step 2 – Shut Off Gas Service
Before making new gas line cuts or disconnecting gas pipe joints, shut off the gas between your connection point and the street gas pipe. Next, cut your existing line pipe where you plan to make your connection. Depending on the type of pipe your gas runs through in your house, use the type of pipe cutter that will work best.
Step 3 – Install Gas Line into the Fireplace
If your pipe is to run from your basement and through your floor to connect to the new fireplace, drill a hole in the floor nearby or up through floor of the fireplace itself, whichever will be closer to your gas pipe route. Run the other end of the gas line to the place where you cut the gas pipe. Then, attach a brass fitting to the fireplace gas valve, applying plumbers tape to the threads and tightening with a pipe wrench.
Step 4 – Connect Fireplace Line to the Gas Pipe
At the gas pipe where you made the cut, install a T-fitting that will connect both ends of the cut pipe and the fireplace pipe. Cut out a piece from the gas pipe long enough that both ends will fit on the T-fitting. Then, fit the end of the fireplace pipe on the unused end. Secure all three connections with plumbers tape or putty.
Instruction manual; JR XP6102 Instruction Manual. You must make sure that the center pin of your JR CHARGER PIGTAIL FOR RECEIVER transmitter is always connected to the negative voltage for correct polarity hookup. • Do not extend the transmitter antenna at XP6102. 6 XP6102 - Introduction 2A X-6102 TRANSMITTER The computer-designed, ergonomically. Instruction Manual Instruction Manual TRANSMITTER SPECIFICATIONS 3B TYPE AIRPLANE HELICOPTER. Your JR transmitter is always connected to the negative voltage for correct polarity hookup. Jr xp6102 transmitter manual.
When finished, turn the gas back on and test all connections by spraying soapy water on them from a spray bottle. If you see bubbles at any of the connections, this means the connection with the bubbles is not tight. You'll need to tighten it further, or reconnect it with more plumbers tape or putty. It's also not a bad idea to get the line inspected professionally after your install, just to be sure everything is as safe as it should be.
With any loose connections and leaks taken care of, your old wood-burning fireplace is ready to receive a new gas replacement.
Explore this ArticlePrepare the FireboxInstall new gas logs.Ask a QuestionRelated ArticlesReferences
How To Install Gas Logs In Fireplace
If you love the ambiance of a wood burning fireplace, but don’t like the mess and inconvenience of building a fire, upgrading your fireplace with gas burning logs can be an easy and affordable solution. Most traditional wood burning fireplaces can be converted into a gas burning application with some minor tweaks and upgrades. If you already have gas logs installed in your firebox, you can upgrade your gas log set to a more modern design, which will improve the heat and usability of your gas logs.
Please note, gas appliances such as a gas log set can cause serious risk to your health and safety if not installed and maintained properly. Such risks include danger of gas leaks, explosion, fire, and carbon monoxide (CO) poisoning. Installation of the gas line should be conducted by a locally licensed and certified professional. Prior to working on your gas log set, ensure the gas line has been fully shut off. Once you're finished working on the logs, ensure there are no leaks by following the procedures in Part 2.
If you notice the smell of gas from the appliance, turn off the gas supply (at the appliance) immediately and contact a certified gas fireplace repair technician for assistance. If you notice the smell of gas, but cannot identify the source, leave your home immediately and contact your local gas company for further assistance.